RFID Module
-
-
JMY6011
-
JMY6011 is based on NXP RC663 chip design. It supports UART or IIC and USB
HID interface and fully compatible with ISO14443 Type A and ISO14443 Type B
and ISO15693 protocols. The dimension is 60mm * 60mm * 5.7mm.
-
-
-
JMY6022
-
JMY6022 is a contactless IC card embedded reading and writing module
designed based on the NXP scheme. It fully supports the MIFARE series and
ISO14443A and ISO14443B T=CL non-contact CPU cards. The RF communication
protocol supports the EMV2010 and PBOC 3.0 certification requirements.The
dimension is 100mm * 70mm * 12mm.
-
-
-
JMY6025
-
JMY6025 is a contactless IC card embedded reading and writing module
designed based on the NXP scheme. It fully supports the MIFARE series and
ISO14443A and ISO14443B T=CL non-contact CPU cards. The RF communication
protocol supports the EMV2010 and PBOC 3.0 certification requirements.The
dimension is 100mm * 70mm * 12mm.
-
-
-
JMY6122
-
JMY6122 is based on NXP CL RC663 chip design. It supports USB HID, RS232C,
UART or IIC interface and fully compatible with ISO14443 Type A and ISO14443
Type B, ISO15693 and ISO7816(4 SAM Slots) protocols. Also it supports NFC
functions. The dimension is 86.5mm * 65mm * 11.2mm.
-
-
-
JMY6123
-
JMY6123 is based on NXP CL RC663 chip design. It supports RS232C, UART
interface and fully compatible with ISO14443 Type A and ISO14443 Type B,
ISO15693 and ISO7816(4 SAM Slots) protocols. Also it supports NFC functions.
The dimension is 79mm * 55mm * 7.5mm.
-
-
-
JMY6223
-
JMY6223 is a modular circuit. User need send the reading or writing commands
to the Contactless IC Card via it. This module complies with LEVEL 1
standard of EMV2000, EMV2010 and PBOC 2.0.It adopts a surface mount
installation form, and its ultra-small size is a major feature.The Dimension
is 22mm*35mm*4.1mm.
-
-
-
JMY6281
-
JMY6281 is based on NXP PN512, CV520 chip design. It supports USB HID, UART
or IIC interface and fully compatible with ISO14443 Type A, ISO14443 Type B
protocols and also NFC function. The dimension is 50.8mm * 50.8mm * 5mm.
-
-
-
JMY6804
-
JMY6804 is based on NXP CL RC663 chip design. It supports USB HID, RS232C,
UART or IIC interface and fully compatible with ISO14443 Type A and ISO14443
Type B, ISO15693 and ISO7816(2 SAM Slots) protocols. The dimension is 70mm *
50mm * 16.5mm.
-
-
-
JMY5011
-
The module and antenna are separate design. 4 wires are linked the antenna
and module. Normally the wire should be less than 200mm. The interface is
UART & IIC. The module supports series IC cards according to ISO14443A,
ISO14443B, ISO15693 and the MIFARE series. And also it supports auto
detecting card.
-
-
-
JMY5041
-
JMY5041 series are the high performance and low cost RFID Module. And the
module and antenna are separate design. 4 wires are linked the antenna and
module. Normally the wire should be less than 200mm. The interface is UART
& IIC. The module supports series IC cards according to ISO14443A,
ISO14443B and the MIFARE series. And also it supports auto detecting card.
-
-
-
JMY5051
-
JMY5051 is the second generation product based on JMY505 with UART and IIC
serial port. JMY5051 has various functions and supports multi ISO/IEC
standard of contactless card. The RF protocol is complex. The designer
combined some frequent used command of RF card and then user could operate
the cards with full function by sending simple command to the module.
-
